Yamaha rx-v430 service manual

Refer to the operation instructions for the component. Adjust the volume to the desired level. The volume level is displayed digitally. You can select the type of input signals you desire. For details about each program, see pages 29 to Page Digital Sound Field Processing Dsp The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound field. The processor controls the strength and delay time of the signals output from the three effect speakers to localize the virtual sound sources and fully encompass the listener.

It recreates comprehensive movie sound design in your audio room. Page Dolby Pro Logic Dolby Surround software into 5 discrete full-range channels 3 channels in front and 2 channels in rear. Page 37 The following list gives you a brief description of the sound fields produced by each of the DSP programs.

Keep in mind that most of these are precise digital recreations of actual acoustic environments. Select the DSP program that you feel sounds best regardless of the name and description given for it below. Page Tuning Automatic and manual tuning There are 2 ways to tune; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. This function enables this unit to automatically tune in to FM stations with strong signals, and to store up to 40 8 stations x 5 groups of those stations in order.

Page Tuning In To A Preset Station Tuning in to a preset station You can tune any desired station simply by selecting the preset station number under which it was stored. Page Sleep Timer Use this feature to automatically set this unit in the standby mode after the amount of time you have set. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source.

Page Recording Recording adjustments and other operations are performed from the recording components. Refer to the operation instructions for these components. The entire range of the main left and right channel signal is directed to the main left and right speakers. The LFE signal carries the low-frequency special effect sound which is only added to certain scenes.

To control other components, you must set up the remote control with the manufacturer codes. Control area Note, however, that some buttons may not operate your component. Once you select an input source, the remote control switches to the mode for operating the component. Adjustment should be made with the remote control. The larger the value, the later the sound effect is generated. The delay time can be individually adjusted to all DSP programs. Adjustments should be made with the remote control.

Page Troubleshooting Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

I General Page 57 Problem The sound suddenly The protection circuit has been activated goes off. The sleep timer has functioned. The sound is muted. Only the speaker on Incorrect cable connections.

The sound effect It is not possible to record the sound cannot be recorded. There is distortion, and There is multipath interference. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.

If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers in your configuration after you finish connecting your speakers.

First, tighten the knob RX-V open the tab and then insert the banana plug connector into the end of the corresponding terminal. If so, slide the switch all the way to either position when this unit is in the standby mode. Select the switch position left or right according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode. Do not connect this unit or other components to the mains power until all connections between the components have been completed.

Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit. This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables.

To enjoy multi-channel sound track of DVD software, etc. All digital input jacks are acceptable for kHz sampling digital signals. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly. RX-V There are three types of video jacks as follows:. Transmits color and luminance separately and achives high-quality color reproduction. Signals input through the composite video, S-video and component jacks are only output through the corresponding composite video, S-video, and component jacks.

When using these jacks, refer also to the operation instructions for the component being connected. If the power is off, this unit may distort the sound from other components. Make sure to. Only digital signals are output from. Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Insert the wire into the slot. A properly installed outdoor antenna provides clearer reception than an indoor one.

If you experience poor reception quality, an outdoor antenna may improve the quality. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.

Please check your email for further instructions. Enter a new password. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e If the product has been dropped or damaged in any way, and f When the product exhibits a distinct change in performance - this indicates a need for service.

RANGE dynamic range GUARD memory guard Built-in 5-channel power amplifier Minimum RMS output power 0. Manufactured under license from Dolby Laboratories. Checking the package contents Check your package to make sure it contains the following items. Standby mode In this mode, this unit will consume a small amount of power in order to receive infrared-signals from the remote control. Selects the tuning frequency when the colon : does not appear.

Turn right to increase or turn left to decrease the lowfrequency response. Turn right to increase or turn left to decrease the highfrequency response. Remote control This section describes the remote control controls and their functions. Used when setting up the manufacturer code see page Speakers This unit has been designed to provide the best soundfield quality with a 5-speaker system, using main left and right speakers, rear left and right speakers and a center speaker.

Speaker placement Refer to the following diagram when you place the speakers. RX-V 1 Unscrew the knob. RX-V 1 Open the tab. RX-V U. Before connecting components CAUTION Do not connect this unit or other components to the mains power until all connections between the components have been completed.

Make sure to connect this unit to both a source component and a recording component using the video jacks of the same system. Connect each antenna correctly to the designated terminals. A good STEP earth ground is a metal stake driven into moist earth. Insert the cable wire into the slot, and clamp it with pliers. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.

Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. Checking the package contents Installing batteries in the remote control Front panel Remote control Using the remote control Front panel display Speaker placement Connecting the speakers Before connecting components Connecting video components Connecting audio components Connecting the antennas Connecting an external decoder Connecting the power supply cords Turning on the power Using the test tone Input modes and indications Selecting a sound field program Understanding sound fields Hi-Fi DSP programs Automatic and manual tuning Presetting stations Tuning in to a preset station Exchanging preset stations Setting the sleep timer Canceling the sleep timer Control area